Overview
Supporting intelligent enclosed wash machines for Liugang’s Zone B raw material yard ultra-low emission retrofit: a 20 m enclosed frame, fully automatic quartz-sand backwash filtration and a 304 stainless steel control cabinet, benchmarked to Liugang’s ultra-low emission monitoring standards.
Client Profile
The project forms part of Liugang’s Zone B raw material yard ultra-low emission retrofit. One machine is installed at the Zone B raw material plant exit and one at the ore logistics park exit — two in total, both outdoors. The site is in Liuzhou, Guangxi, in a mid-subtropical monsoon climate: annual average temperature 18.1–19.4 °C, minimum ambient temperature -2.5 to -5.8 °C, annual average relative humidity 74.5%, annual rainfall 1,345–1,940 mm, with seismic design intensity of 6 degrees. Equipment supplied must be technically mature, safe, reliable, stable in operation, easy to maintain, and energy-saving.
The Challenge
- The equipment must satisfy the Technical Guide for Ultra-Low Emission Retrofits in the Steel Industry (CMEA [2020] No. 4), Liugang Group’s ultra-low emission retrofit implementation plan (Group [2023] No. 27) and the company’s ultra-low emission monitoring facility requirements and standards.
- Vehicles to be washed are up to 18 m long, 2.9 m wide and 4.5 m high, with a maximum weight of 150 t, and washing is performed on the move.
- The equipment must operate at relative humidity up to 90% RH with a 130% safety overload margin and an annual availability of at least 98%.
- Wastewater must discharge by gravity with no outflow, and desilting is done periodically with an excavator, placing higher demands on settling and filtration.
- Both the electrical and intelligent control cabinets must be 304 stainless steel, at least 2 mm thick, with IP56 protection.
The Solution
Washing and recovery form one closed loop: drive-through washing inside a 20 m intelligent enclosed frame covers sides, underbody, tyres and body; wastewater discharges by gravity from a three-stage settling basin into a quartz-sand filter (fully automatic backwash) and then returns to a 304 stainless steel tank for recirculation. 封闭框架内部 · 冲洗区 | Inside the enclosure · wash zone Intelligent enclosed frame — Enclosed frame 20 m × 5.5 m × 5.5 m; wash time 60–300 s per vehicle (adjustable) at 12–60 vehicles/hour; washing is performed on the move, covering sides, underbody, tyres and body. High-pressure wash system — Wash pressure ≥1.0 MPa; nozzles are 304 stainless steel, universally adjustable (desilting φ3.2 mm, washing φ1.5 mm) and rated to no less than 1.0 MPa, guaranteeing normal operation at ≥1.0 MPa. Water use 40–60 L per vehicle; total installed power 70 kW. Effluent and filtration — Settling in a three-stage basin; discharge by gravity with no outflow; periodic desilting by excavator. Effluent filtration uses quartz sand with fully automatic backwash, supported by a 304 stainless steel tank (with level protection, instruments and valves, capacity not less than 4 m³). Intelligent control module — Control uses a Siemens S1500-series PLC with a 10-inch touch screen (automatic, manual, remote); the IoT module is ForIOT FLINK, Weikong or another client-approved brand; triggering uses high-sensitivity infrared sensors; monitoring uses 4-megapixel Hikvision bullet cameras. The intelligent control cabinet is brushed 304 stainless steel, at least 2 mm thick, IP56.
Project Details
- 封闭框架外部实拍 | Exterior of the enclosure
- A wash rate of 12–60 vehicles/hour with adjustable 60–300 s per vehicle balances throughput and washing quality.
- Water use of 40–60 L per vehicle is markedly lower than conventional washing; annual availability is at least 98%.
- Effluent discharges by gravity with no outflow; a three-stage settling basin plus fully automatic quartz-sand backwash filtration and a 304 stainless steel tank of at least 4 m³ handle the water.
- The control system supports automatic, manual and remote modes with an IoT module, and monitoring uses 4-megapixel cameras.
- Both control cabinets are 304 stainless steel, at least 2 mm thick and IP56-rated, suited to the humid outdoor environment.
- The complete installation meets Liugang’s ultra-low emission retrofit and monitoring facility requirements, directly supporting raw material yard compliance.
In a steel raw-material yard where ultra-low emissions are a hard constraint, the criteria for a wash machine have been rewritten: not “can it wash clean” but “how much water and power it uses, what its annual availability is, and whether regulators can capture its data”. Writing these into the technical agreement and delivering on every clause is the real challenge after winning the contract.
Project Gallery









