Home/Case Studies/Liugang Fangchenggang - 25 m Enclosed Wash Station
Liugang Fangchenggang - 25 m Enclosed Wash Station
Steel & Metallurgy

Liugang Fangchenggang - 25 m Enclosed Wash Station

20 m wash zone in a 25 m unit - 90 kW - six months of video storage feeding the owner control room
客户:柳钢防城港(业主)/ 柳钢设计院 / 南京沪友冶金机械 · 服务方:上海臻欧实业发展有限公司(凯美龙 KAMRON)
← ← Back to all cases

Overview

The Liugang Fangchenggang new wash station project required a long-run washing facility at the raw material yard entrance. KAMRON responded with a 25 m enclosed KM-H3 washer featuring a 20 m wash zone, 90 kW of power, desilting nozzles and six months of video archiving, plus a reserved data interface for the owner. In the same period KAMRON also equipped units for the Liugang design institute and for Nanjing Huyou Metallurgical Machinery.

Client Profile

The Liugang Fangchenggang base is a modern coastal steel production zone. Vehicles entering and leaving the raw material yard are large and travel long distances. With strict control over mud carry-out and material dust, the wash station had to deliver a long wash run plus data traceability and remote retrieval.

The Challenge

  • Raw-material vehicles are long and carry heavy material, so a conventional 10-15 m bay cannot guarantee full coverage.
  • Plate capture and upload were required for vehicles entering the wash system, with video retained over six months and routed to the owner control room.
  • Trenches beneath the wash zone silt up continuously, requiring dedicated mud-flushing nozzles for automatic cleaning.
  • Situated on the coast, the site demands higher corrosion protection than inland plants.

The Solution

KAMRON supplied an enclosed KM-H3 with a 20 x 4.6 x 5.5 m wash zone, a 5 x 4.6 x 5.5 m dewatering/drying zone and a 25 x 4.6 x 5.5 m modular unit. The steel structure uses GB Q235 cold-rolled carbon steel folded as one piece, hot-dip galvanised and coated; high-pressure piping is independently routed DN50 galvanised steel with 304 stainless, universally adjustable nozzles. Wash pressure is at least 1.0 MPa, and embedded desilting lines with mud-flushing nozzles automatically clear silt from the trenches below the wash zone. An HD camera with upload capability, video recorder and hard disk retain over six months of footage routed to the owner control room, with plates captured and uploaded for vehicles entering the system and interfaces reserved. The foundation uses bedding plus concrete for a 150-tonne rating, at 500 L per vehicle and 90 kW. The unit delivered to the Liugang design institute measures 15 x 4.6 x 1.5 m at 50 kW with Siemens PLC, Zhengtai components and an IP55 outdoor cabinet; the Nanjing Huyou units cover three semi-enclosed stations - 12 m at the converter plant alloy warehouse, 15 m at Jinsan yard and 21 m at Lane 21 - at 85 kW and 100 kW, 400-600 L per vehicle and 150-tonne grated foundations.

Project Details

  • A 20 m wash zone lets long raw-material vehicles complete a full wash in one pass, avoiding residual material at the rear.
  • Embedded desilting lines with mud-flushing nozzles automatically clear trench silt, cutting manual cleaning frequency.
  • Over six months of video routed to the owner control room plus plate capture and upload satisfy material-flow traceability and ultra-low-emission ledger requirements.
  • Hot-dip galvanising with anti-rust coating suits the corrosive coastal environment.
  • One delivery batch covering the design institute and three Nanjing Huyou yards gives consistent operation and maintenance across multiple points of the same system.

In raw-material settings characterised by long vehicles, long travel and heavy traceability, the length of the wash zone effectively determines the completeness of the data trail - a short run creates a wash blind spot that no amount of downstream data can compensate for. Length, desilting and monitoring therefore have to be designed as one.

Project Gallery

Ready to upgrade your wash system?

Tell us your vehicle types, site layout and washing needs — KMRON engineers will reply within 2 business days with a tailored proposal and quote.

Get a Quote →